This is an integrated LED tail light retrofit for the stock 2004-2008 Yamaha Road Star Line tail lights (see compatibility list above).  All the internals of the stock tail light unit are replaced with a ultra high-tech Custom LED circuit board containing 32 Ultra Bright Red LEDs and 32 Ultra Bright Yellow LEDs - compared to only 16 red LEDs on the stock circuit board!

This product features our proprietary and patented Blaster-X, Brake Alert and Strobe Mode!  With this product, your turn signals are built right into the tail light!  It's the best fender eliminator money can buy.

Brake Alert automatically provides a few quick ultra-bright strobe pulses of light the instant the brakes are applied.  This alerts motorists the instant you apply the brakes - possibly saving seconds of reaction time for non alert motorists!  The number of pulses can be user-configured VIA our new Programming Interface!  It can also be disabled if desired.

Strobe Mode is a feature that puts the taillight into a devastating strobe cycle that is sure to get anyone's attention.  This mode produces insanely bright pulses of light at ultra high frequencies, in alternating patterns across the tail light.  Strobe mode is engaged by grounding a control wire, and can be engaged at any time.

Blaster-XÔ is our proprietary pulse-width-modulation technology that squeezes the maximum possible illumination power out of LEDs.  The result is a significantly less expensive, yet even more outstanding and effective product than it's predecessors - and widens our advantage over our competitors.

NEW! This product also marks the introduction of our NEW Programming Interface which allows users to easily customize features of the tail light!  The customizable features menu allows users to:

• Enable or Disable the Startup Sequence.
• Set the number of pulses in the Brake Alert feature (can set to zero to disable Brake Alert).
• Adjust the running light brightness within a preset range.
• Adjust the brake light brightness within a preset range.
• Engage Demo Mode, where the tail light cycles through all functions automatically and repeatedly!
• Reset factory defaults.

This programming interface is accessed very simply through the Strobe Mode control wire!  The interface is designed to receive input simply by providing ground pulses to the strobe mode control wire.  No special equipment is necessary to access and utilize the programming interface!  Detailed programming instructions will ship with every unit.

NEW! And last but not least, our Sure-Blink Technology.  Our Integrated Tail Lights are designed to follow the turn signal commands of the motorcycles flasher relay.  This insures it is compatible with all after market and OEM flasher relays - especially programmable relays such as our ELFR-P.  However, in the event that the tail light receives a command to blink that does not break (blink) within a preset time period, the tail light will automatically blink that side.  This feature is most useful in preventing common no-blink problems that are associated with retrofitting motorcycles to LEDs.

Just as on the other Custom LED integrated LED tail light models, the system is designed so that the red LEDs turn off (on one side) when the yellow LEDs come on, so that the turn indication is a pure and distinct yellow light.  The unit automatically flashes between the red and yellow on the side you're turning!  The Yellow LEDs are slightly offset as well, creating a dramatic attention grabbing effect.

The engineering is solid and dependable, the looks are unbeatable, and the brightness is incredible!  Don't waste your time with half hearted solutions, do it the right way from the start, with Custom LED.

If you would like to find out more information as to Custom LED's design concepts for the Integrated LED Tail Lights, and the purpose of them, read this introduction to Custom LED's Integrated LED Tail Lights.

Custom LED Yamaha Road Star Blaster-X Integrated LED Tail Light Features:

• 32 Ultra Bright Red LEDs for running and brake lights.
• 32 Ultra Bright Yellow LEDs for turn signals.
• Custom LED ColorChange Technology on-board.
• Custom LED Blaster-X PWM technology on-board.
• Custom LED Strobe Mode!
• Custom LED Brake Alert!
• New Programming Interface allows users to easily customize features!
• New Sure-Blink Technology
• Robust regulated design for consistent and reliable performance.
• 4 MHz microprocessor controlled operation.
• Detailed step by step instructions with illustrations for a simple install.
• Smart color matched wires matches motorcycle wires for easy wiring.
• Only 3 wires to hook up outside of tail light housing.
• All electrical connectors and hardware provided with kit.
• 24/7 customer support.
• 2-year Warranty & Satisfaction Guarantee!
• MADE IN THE USA!
• NOT DOT approved.

 

STOCK YAMAHA ROAD STAR TAIL LIGHT PCB

---

CUSTOM LED YAMAHA ROAD STAR BLASTER-X INTEGRATED LED TAIL LIGHT PCB

Circuit board installs into OEM tail light housing according to provided instructions.

At the moment, we do not have a video specifically of the Yamaha Road Star Blaster-X Integrated LED Tail Light, but our R1 Blaster-X Video shows the same features.  Watch the video below:

CLICK HERE TO SEE BLASTER-X VIDEO

NOTE: It is very difficult to properly videotape these high-intensity integrated LED tail lights.  We have yet to find a camera that is capable of accurately reproducing the intensity and clarity of our product. 

In the video, the pulses in the brake alert feature and strobe mode feature are faster than the cameras frame rate.  As a result the video does not show the full intensity and high speed pulses of these features.

Furthermore, the amber LEDs for the turn signals is clearly and distinctly amber in person.  For some reason, the amber always shows up as red in the videos.

We are looking for better videos to properly portray our products.  If you own a Blaster-X Tail Light and are able to capture accurate video, Custom LED will BUY your video!  Please contact us.

The Custom LED Yamaha Road Star Blaster-X Integrated LED Tail Light retrofit kit must be installed into the OEM tail light.

There may be additional accessories required to correct blinker problems on your motorcycle if you remove your OEM turn signals.  These accessories could not be built into the tail light, and are generally optional and specific to different customers needs, so they are sold separately. Please see the recommended accessories above, and read about the general issues and solutions in our Frequent Questions Page.  If you have any questions, please do not hesitate to contact us.

Installation of this product requires that you remove the OEM tail light from the motorcycle for the retrofit kit installation.  Please consult a qualified technician or your repair manual for the proper procedure to remove the OEM tail light.

Once the OEM tail light is removed from the motorcycle, installation of the Custom LED Integrated LED Tail Light is detailed in the instructions below.

click icon to download

 

Adobe Acrobat Reader is required to view this file.

If you are having problems viewing the file, please download the free software here.

Custom LED consistently receives rave reviews from our customers about our products!  We try to post a representative group of them on our feedback page on this site, but we can't post them all! 

Our Feedback Profile on our Ebay Auctions are a great way to see what our customers think of our products, because Ebay promotes honest feedback.  Take a look at our Ebay Feedback!

Our commitment to quality, honesty, ingenuity and customer service is really making an impact in an industry full of careless "sell anything" retailers and hack-artist copy-cats.  Trust in our products, and see for yourself...